top of page
Search

House Repointing Guide Different Brick Types and the Mortar They Need

Dna pointing
3 hours ago
10 min read

Bad repointing can make a wall look tidy for a season, then trap damp, crack brick faces, and speed up decay. The mortar between bricks is not just filler. It is part of the wall’s weather protection, movement control, and moisture management.


That is why matching mortar to brick type matters. A hard modern cement mix might suit dense engineering brick, but it can damage soft handmade brick. A lime mortar that works beautifully on a Victorian terrace may not be right for a modern cavity wall in a very exposed spot.


This house repointing guide explains the main brick types found in UK homes, the mortar they usually need, and why the wrong choice causes problems.


Close-up view of weathered brickwork being repointed by hand
Good repointing starts with understanding both the brick and the old mortar.

Why the mortar must suit the brick


Bricks and mortar work as a pair. The best mortar is usually slightly softer and more breathable than the brick. That gives the wall a sacrificial joint. Rain, frost, salts, and movement affect the mortar first, rather than the brick face.


When the mortar is too hard, several things can happen:


  • Moisture cannot evaporate easily through the joints.

  • Water moves into the brick instead.

  • Frost can blow the face of the brick.

  • The wall may crack because the joints cannot absorb small movement.

  • Repairs become harder because the brick fails before the mortar does.


Older homes were often built with lime mortar because lime handles moisture and movement well. Many modern homes use cement-based mortar because the bricks are harder, the walls are designed differently, and the construction tolerances are different.


The aim is not to choose the “strongest” mortar. The aim is to choose the most compatible mortar.


The main mortar types used for repointing


Before looking at brick types, it helps to understand the common mortar options.


Lime putty mortar suits soft and historic brickwork


Lime putty mortar is made from lime putty and sand. It cures slowly by absorbing carbon dioxide from the air. It remains flexible and breathable, which makes it especially useful for older solid walls.


It is often suitable for:


  • Georgian, Victorian, and Edwardian brickwork

  • Handmade or soft red bricks

  • Historic solid wall construction

  • Listed and conservation-area buildings, subject to the right advice


Lime putty mortar is not the fastest material to work with. It needs protection from heavy rain, frost, direct drying winds, and hot sun while it cures. When used correctly, it helps old brickwork dry out naturally.


Natural hydraulic lime works where more set is needed


Natural hydraulic lime, often called NHL, sets through a chemical reaction with water as well as by exposure to air. It is still breathable, but it gains strength more quickly than lime putty.


Common grades include NHL 2, NHL 3.5, and NHL 5. The higher the number, the stronger and less flexible it tends to be.


As a broad guide:


Mortar type

Typical use

Main qualities

Lime putty mortar

Soft historic brickwork in sheltered conditions

Very breathable, flexible, slow curing

NHL 2

Soft brickwork and less exposed elevations

Breathable, gentle, moderate set

NHL 3.5

General older brickwork and moderate exposure

Balanced strength and breathability

NHL 5

Harder masonry and more exposed locations

Stronger, faster set, less forgiving

Cement-lime-sand mortar

Many modern brick walls

Durable, workable, less breathable than lime

Cement-sand mortar

Dense modern bricks and engineering bricks

Hard and strong, but often unsuitable for old brickwork


These are general pointers, not fixed rules. A good repointing job should also consider the existing mortar, wall condition, exposure, joint width, and whether the wall is solid or cavity construction.


Cement-based mortar suits many modern walls


Cement mortar is stronger and less porous than lime mortar. That can be useful on modern brickwork, especially where the bricks are dense and the wall has a cavity, damp-proof course, cavity trays, and modern detailing.


A common modern pointing mix includes cement, lime, and sand. The lime in this mix improves workability, but it does not make the mortar behave like traditional lime mortar.


Pure hard cement mixes can be risky on older homes. They may look sharp at first, but they often cause long-term damage when used with soft brick.


Soft red bricks need breathable lime mortar


Soft red bricks are common in older UK houses. They were often fired at lower temperatures than modern bricks, which makes them more porous and less uniform. Many have a warm red or orange tone, rounded arrises, and small variations in size.


These bricks usually need a lime-based mortar, often lime putty or a weaker NHL. The reason is simple. Soft brick absorbs and releases moisture. The mortar needs to do the same, ideally more readily than the brick.


A hard cement mortar can trap moisture in these bricks. In winter, that moisture can freeze, expand, and push off the brick face. This is called spalling. Once it starts, repointing alone may not fix it because the brick surface has already failed.


For soft red brick, look for:


  • A breathable lime mortar

  • Sand that matches the original colour and grain

  • A joint finish that sheds water without sealing the wall

  • Careful raking out by hand or with suitable low-impact tools


The joint profile matters too. Flush, slightly recessed, or weather-struck joints may all be found on older buildings, but the finish should suit the age and style of the wall. Overly deep recessed pointing can leave soft brick edges exposed to rain.


Handmade and clamp-fired bricks need gentle repair


Handmade bricks are often uneven, with irregular faces and varied colours. Clamp-fired bricks may show darker patches, overburnt sections, or softer areas. These bricks give old houses much of their character, but they also need careful handling.


The mortar should usually be lime-based and softer than the brick. A lime putty mortar is often appropriate for sheltered elevations. NHL 2 or NHL 3.5 may be used where a slightly firmer set is useful, but the condition of the brick should guide the choice.


With handmade brickwork, neatness should not mean making the wall look new. The goal is to repair the joints while keeping the character of the masonry.


Common mistakes include:


  • Cutting joints too wide with grinders

  • Using bright grey cement mortar

  • Smearing mortar over uneven brick faces

  • Creating sharp modern joints on irregular old brickwork


Hand raking is slower, but it protects fragile brick edges. If a power tool is used, it should be controlled by someone who understands historic brickwork.


Eye-level view of varied handmade bricks with lime mortar joints
Irregular handmade bricks often need softer mortar and careful joint finishing.

London stock bricks usually need lime-rich mortar


London stock bricks are yellow, buff, or brownish bricks seen across many older properties in London and the South East, though similar stock bricks appear elsewhere. They can vary from fairly soft to moderately dense.


Many older stock brick walls were built with lime mortar. Repointing them with hard cement can change how the wall handles moisture, leading to damp patches, salt deposits, or damaged brick faces.


A lime-rich mortar is often the right starting point. Depending on the brick and exposure, that may mean lime putty, NHL 2, or NHL 3.5. The sand choice is especially important because the colour of the mortar can strongly affect the look of stock brickwork.


For many stock brick homes, the best repair is one that almost disappears after weathering. That means matching:


  • Mortar colour

  • Grain size

  • Joint width

  • Joint profile

  • Texture after brushing back


Fresh lime mortar may look pale at first, then settle and mellow as it cures and weathers.


Dense modern bricks can take stronger mortar


Modern facing bricks are generally harder and more consistent than older handmade bricks. They are often used in cavity wall construction, where the outer leaf deals with weather and the cavity helps manage moisture.


These bricks can usually tolerate a stronger mortar than soft historic brick. A cement-lime-sand mortar is common for modern repointing. The lime improves workability and helps the mortar bond well, while cement gives strength and weather resistance.


That said, stronger does not mean careless. The new mortar still needs to match the existing wall in colour, texture, and joint finish. If the repair patch stands out, the wall can look pieced together.


For modern facing brick, the repointing decision depends on:


  • The hardness and porosity of the brick

  • The original mortar type

  • The exposure of the wall

  • Whether cracks suggest movement

  • Whether damp is coming from failed detailing rather than the joints


Repointing will not fix blocked cavities, failed damp-proof courses, leaking gutters, or poor ground levels. It may help, but only if the joint failure is part of the problem.


Engineering bricks need strong, dense mortar


Engineering bricks are very dense, hard, and water-resistant. They are often blue, red, or dark brown and commonly used below damp-proof course level, around plinths, in retaining details, and in areas that need high strength.


Because engineering bricks are so hard, they normally need a stronger mortar than soft brickwork. Cement-based mortars are often suitable. In some cases, a stronger NHL may be considered, but the design and exposure matter.


The key issue is bond. Dense bricks do not absorb much water from the mortar, so workmanship becomes very important. The joints must be properly filled and compacted.


Repointing engineering brickwork often needs:


  • Thorough cleaning of the joint

  • Correct moisture control before pointing

  • Firm compaction of mortar

  • A durable joint profile

  • Careful curing to avoid rapid drying


Using a very soft lime mortar with dense engineering bricks may lead to weak, friable joints in exposed areas. The mortar must still be compatible, but it also needs enough strength for the setting.


Fletton and common bricks vary more than people expect


Fletton bricks, common bricks, and other utilitarian bricks appear in many UK homes, extensions, garden walls, and internal walls. Some are reasonably hard. Others are porous and should not be treated like modern facing bricks.


If these bricks are exposed externally, the mortar choice should follow the brick’s actual condition rather than its name. A weathered common brick in an old solid wall may need lime mortar. A harder brick in a mid-to-late twentieth-century cavity wall may suit cement-lime-sand mortar.


This is where testing and inspection help. A contractor may look at how easily the old mortar rakes out, whether the brick face powders, how the wall dries after rain, and whether previous cement repairs have caused damage.


A small trial panel is often useful. It shows the colour, texture, and finish before a whole elevation is repointed.


Calcium silicate and concrete bricks need careful matching


Calcium silicate bricks, sometimes called sand-lime bricks, are usually pale, smooth, and regular. Concrete bricks and blocks can also appear in later housing and garden structures.


These materials behave differently from traditional fired clay brick. They can be affected by movement, moisture, and salts in their own ways. Mortar choice should match the original construction as closely as possible.


Cement-lime-sand mortar is often used, but the mix should not be guessed. The joint finish also matters because smooth pale bricks show staining and smears more easily than textured clay bricks.


Cleaning after repointing should be gentle. Harsh acid cleaning can damage certain masonry materials and alter the appearance of the wall.


How to identify the right mortar before repointing


Good repointing starts before any new mortar is mixed. The existing wall gives clues.


Look at the brick first. Soft, weathered, irregular brick usually points towards lime. Dense, sharp-edged modern brick may suit a cement-based mix. Next, inspect the old mortar. Lime mortar is often softer and can be scratched more easily. Cement mortar is harder, greyer, and more brittle.


The wall’s age matters, but it is not the only guide. Some older homes have been repointed badly in cement already. Some newer walls include softer bricks than expected.


A practical assessment should include:


  • Brick hardness and porosity

  • Existing mortar type

  • Joint depth and condition

  • Wall exposure to wind-driven rain

  • Signs of damp, salts, cracking, or spalling

  • Previous repairs and coatings

  • The building’s age and construction type


For listed buildings or homes in conservation areas, speak to the relevant local authority or a conservation professional before changing the mortar or joint style.


Why sand is as important as binder


Mortar is not just lime or cement. Sand makes up most of the mix, so it has a huge effect on performance and appearance.


Sharp, well-graded sand helps create a strong, open-textured mortar. Very fine sand can make mortar dense and prone to shrinkage. The colour of the sand also affects the final shade more than many people expect.


On old brickwork, a good mortar match often comes from the right local-looking sand rather than pigment. Pigments can be useful in small amounts, but too much can create an artificial colour that does not weather naturally.


The ideal repointing mortar should match:


  • Strength

  • Breathability

  • Texture

  • Colour

  • Joint profile

  • Weathering behaviour


A mortar that matches only the colour is not a proper match.


Common repointing mistakes to avoid


The most damaging repointing mistakes usually come from speed, wrong materials, or poor preparation.


One common problem is raking out joints too shallow. New mortar needs enough depth to bond properly. As a broad principle, joints are usually raked out to a depth that gives the new mortar a secure key, while taking care not to damage the brick.


Another mistake is pointing over damp, dirty, or loose joints. The new mortar may look fine at first, then crumble or detach.


Avoid these errors:


  • Using hard cement on soft historic brick

  • Applying mortar in freezing, very hot, or very wet weather

  • Leaving joints underfilled behind a neat surface

  • Smearing mortar across brick faces

  • Using an unsuitable grinder on fragile brickwork

  • Repointing without fixing leaks, gutters, or drainage issues


Curing matters as much as mixing. Lime mortar especially needs time and protection. If it dries too quickly, it can become weak and dusty. If frost hits before it has cured enough, it can fail.


What good repointing should look like


Good repointing should look calm, not flashy. The joints should be full, compacted, and finished in a style that suits the building. The brick faces should be clean. The colour should sit comfortably with the wall, even if it takes a little time to weather in.


More than anything, the wall should work better. Rain should shed properly. Moisture should have a route out. Soft bricks should not be trapped behind hard mortar. Dense bricks should have joints strong enough to stand up to exposure.


The right mortar protects the brick, not the other way round. For older UK homes, that often means lime. For many modern homes, it may mean a cement-lime-sand mix. For engineering brick, it usually means a stronger, denser mortar. The skill is knowing which wall is in front of you.


Choose the mortar to match the brick, the age of the property, and the exposure of the wall. That is how repointing becomes a proper repair, rather than a short-lived cosmetic job.


 
 
 

Comments


bottom of page